IJFTET
International Journal of Futuristic Trends in Engineering and Technology
UGC and ISSN Approved and added in the UGC Approved List of Journals Journal.
IJFTET Volume II, Issue VI, May - 2015
(Paper ID: 26ET3005201501)
Factor Affecting to Selection of Supplier Using RII Method
Document Information:
Title: Factor Affecting to Selection of Supplier Using RII Method
Author(s): Mr. Jaydeep D. Agola, P.G. student, At S.N.P.I.T. & R.C, UMRAKH-BARDOLI, bhopali@yahoo.com. Dr. H. R. Patel, Professor, At S.N.P.I.T. & R.C, UMRAKH-BARDOLI. Prof. Bhavin K. Kashiyani, Asst. Professor, At S.N.P.I.T. & R.C, UMRAKH-BARDOLI. bhavinkashiyani@gmail.com
Citation: Mr. Jaydeep D. Agola, Dr. H. R. Patel & Prof. Bhavin K. Kashiyani. "Factor Affecting to Selection of Supplier Using RII Method", IJFTET, Volume: II , Issue: VI Publication Year: 2015 , Page(s): 1-5.
Keywords: supplier selection.
Article type: Research paper
DOI: 30/05/2015 http:http://ijftet.wix.com/research#!vol-ii-issue-vi-may15/cxz0 (Permanent URL)
Publisher:Akshar Publication
Abstract: With increasingly competitive global world markets, companies are under intense pressure to find ways to cut production and material costs to survive and sustain their competitive position in their respective markets. However, numerous government reports have criticized the industry's poor performance, especially in terms of quality, quantity and delivery. The preliminary data for this research was collected through a literature review and the use of a questionnaire survey. Few experts were interviewed to identify factors which affect supplier selection in construction projects. As the outcome, total 38 factors that affect supplier selection may be encountered in a construction project were identified. An approach is suggested to carry out ranking of these supplier selection factors by Relative importance index [RII].
(Paper ID: 26ET3005201502)
Ranking to the Factors Affecting Contractor Performance Using RII Method
Document Information:
Title: Ranking to the Factors Affecting Contractor Performance Using RII Method
Author(s): Mr. Mihirkumar B. Naik, P.G. student, At S.N.P.I.T. & R.C, UMRAKH-BARDOLI, themihir91@yahoo.in. Dr. Neerajkumar D. Sharma, Professor At S.N.P.I.T. & R.C, UMRAKH-BARDOLI, neerajrwh@gmail.com. Prof. Bhavin K. Kashiyani, Asst. Professor, At S.N.P.I.T. & R.C, UMRAKH-BARDOLI. bhavinkashiyani@gmail.com
Citation: Mr. Mihirkumar B. Naik, Dr. Neerajkumar D. Sharma & Prof. Bhavin K. Kashiyani. "Ranking to the Factors Affecting Contractor Performance Using RII Method", IJFTET, Volume: II , Issue: VI Publication Year: 2015 , Page(s): 6-11.
Keywords: Contractor performance, Relative important index, Respondent
Article type: Research paper
DOI: 30/05/2015 http:http://ijftet.wix.com/research#!vol-ii-issue-vi-may15/cxz0 (Permanent URL)
Publisher:Akshar Publication
Abstract: The construction industry often acts as a catalyst to stimulate the growth of a nation's economy. The industry is often referred to as an engine of growth. However, numerous projects have criticized the industry's poor performance, especially in terms of productivity, quality, quality systems, cost overrun and time overrun. In order to improve performance, many construction companies implement the ISO 9000 series, an integrated system to ensure consistency and better performance of construction projects. The preliminary data for this research was collected through a literature review and the use of a questionnaire survey targeted at some contractors, clients and consultants in some projects in India. Few experts were interviewed and their opinions were taken to identify factors which affect contractor performance in construction projects. As the outcome, total 86 factors that affect contractor performance may be encountered in a construction project were identified. The factors for contractor performance are then classified into twelve broad categories (Cost, Time, Quality, Management, Material, Worker, Health and Safety, Client Satisfaction, Environmental, Execution, Design and Documentation, Productivity) depending on their nature and mode of occurrence. An approach is suggested to carry out ranking of these contractor performance factors by Relative importance index technique.
(Paper ID: 26ET3005201503)
The Impact of the Dark Web on Internet Governance and Cyber Security
Document Information:
Title: The Impact of the Dark Web on Internet Governance and Cyber Security
Author(s): Prof. Nehal B. Shah, Ph.D. Scholar, Rai University, Ahmedabad. Gujarat. Dr. Ravikumar K., Director of Academics, Shankara eye Hospital
Citation: Prof. Nehal B. Shah & Dr. Ravikumar K.. "The Impact of the Dark Web on Internet Governance and Cyber Security", IJFTET, Volume: II , Issue: VI Publication Year: 2015 , Page(s): 12-16.
Article type: Research paper
DOI: 30/05/2015 http:http://ijftet.wix.com/research#!vol-ii-issue-vi-may15/cxz0 (Permanent URL)
Publisher:Akshar Publication
Abstract:
With the Internet Corporation for Assigned Names and Numbers’ contract with the United States Department ofCommerce due to expire in 2015, the international debateon Internet governance has been re-ignited. However, much of the debate has been over aspects of privacy andsecurity on the visible Web and there has not been muchconsideration of the governance of the “deep Web” andthe “dark Web.”The term deep Web is used to denote a class of contenton the Internet that, for various technical reasons, is notindexed by search engines. The dark Web is a part ofthe deep Web that has been intentionally hidden and isinaccessible through standard Web browsers. A relativelyknown source for content that resides on the dark Web isfound in the Tor network. Tor, and other similar networks, enables users to traverse the Web in near-complete anonymity by encrypting data packets and sending themthrough several network nodes, called onion routers. Like any technology, from pencils to cellphones, anonymity can be used for both good and bad. Users whofear economic or political retribution for their actions turnto the dark Web for protection. But there are also thosewho take advantage of this online anonymity to use the dark Web for illegal activities such as controlled substancetrading, illegal financial transactions, identity theft andso on.
Considering that the dark Web differs from the visible Web, it is important to develop tools that can effectively monitor it. Limited monitoring can be achieved today by mappingthe hidden services directory, customer data monitoring, social site monitoring, hidden service monitoring andsemantic analysis.
(Paper ID: 26ET3005201504)
Feasibility Study of Sustainable Construction Material Using 3R Concept
Document Information:
Title: Feasibility Study of Sustainable Construction Material Using 3R Concept
Author(s): Mr. Krunal V. Mistry, P.G. student, At S.N.P.I.T. & R.C, UMRAKH-BARDOLI, mistry.krunal0@yahoo.com. Prof. Bhavin K. Kashiyani, Asst. Professor, At S.N.P.I.T. & R.C, UMRAKH-BARDOLI, bhavinkashiyani@gmail.com. Dr. H. R. Patel, Professor, At S.N.P.I.T. & R.C, UMRAKH-BARDOLI.
Citation: Mr. Krunal V. Mistry, Prof. Bhavin K. Kashiyani & Dr. H. R. Patel. "Feasibility Study of Sustainable Construction Material Using 3R Concept", IJFTET, Volume: II , Issue: VI Publication Year: 2015 , Page(s): 17-20.
Keywords: reuse, recover, and recycle, construction waste, sustainability.
Article type: Research paper
DOI: 30/05/2015 http:http://ijftet.wix.com/research#!vol-ii-issue-vi-may15/cxz0 (Permanent URL)
Publisher:Akshar Publication
Abstract: In the construction industry mostly the waste obtain from demolition of structure are used for landfill. Now days the price of land is also increasing faster, so it is necessary to take some action to stop the activity of land filling and save the land for future work and also save the environmental condition. Sustainable construction means to adopt the building design which have sustainable supply and environmentally friendly. In this study the approach of using recycled, reused material in the new construction project or in other work which is related to the construction is detailed. This approach is made clear by checking the feasibility of usage of 3r material in market. From this study around 37% to 38% of the materials can be reutilized in the construction work. But still technology is lagging behind to reutilize the waste material into new construction to achieve full sustainability.
(Paper ID: 26ET3005201505)
Voltage Regulation at the Short-Circuit Condition
Document Information:
Title: Voltage Regulation at the Short-Circuit Condition
Author(s): Prince R. Jain, Student of Electrical Engineering Department, Sardar Vallabhbhai Patel Institute of Technology, Vasad, Gujarat, India. pr890456@gmail.com. Parth Y. Gole, Student of Electrical Engineering Department, Sardar Vallabhbhai Patel Institute of Technology, Vasad, Gujarat, India. parthgole.1993@gmail.com
Citation: Prince R. Jain & Parth Y. Gole. "Voltage Regulation at the Short-Circuit Condition", IJFTET, Volume: II , Issue: VI Publication Year: 2015 , Page(s): 21-23.
Keywords: Voltage regulation, Short circuit condition, Resonance, Surge impedance loading (SIL), Compensation of load.
Article type: Research paper
DOI: 30/05/2015 http:http://ijftet.wix.com/research#!vol-ii-issue-vi-may15/cxz0 (Permanent URL)
Publisher:Akshar Publication
Abstract: This paper presents the efficient solution for voltage regulation at the short circuit condition, and ensure that the quality power supply to the load even at the short circuit condition. Scope of this control method is it can be used successfully where continuous power supply is required because we can get desired output voltages even at short-circuit condition. Somehow, it presents the concept of power factor improvement in a different manner to fulfil the aim. Here, the simulation results show that this method is promising for continuous power supply.
(Paper ID: 26ET3005201506)
Design and Analysis of 0.5 ton Jib Crane Performance Characteristics
Document Information:
Title: Design and Analysis of 0.5 ton Jib Crane Performance Characteristics
Author(s): Vakani Chirag Arvindkumar, PG Student, Mechanical Engineering, Gujarat Technological University, India. vakanichirag@yahoo.com. Mr. Shivang S. Jani, Assistant Professor, Gujarat Technological University, India. ssjani@aits.edu.in
Citation: Vakani Chirag Arvindkumar & Mr. Shivang S. Jani. "Design and Analysis of 0.5 ton Jib Crane Performance Characteristics", IJFTET, Volume: II , Issue: VI Publication Year: 2015 , Page(s): 24-27.
Keywords: Floor mounted jib crane, ANSYS, Deformation, Static analysis.
Article type: Research paper
DOI: 30/05/2015 http:http://ijftet.wix.com/research#!vol-ii-issue-vi-may15/cxz0 (Permanent URL)
Publisher:Akshar Publication
Abstract: Today’s industry demands versatile, efficient and cost effective equipment while at the same time providing more flexibility along with significant savings through increased productivity. Cantilever I-type beam is a component of the floor mounted jib crane used in Hi-Tech Industry, which located in Naroda GIDC, Ahmedabad. This component is liable to fail due to excessive loading, by the flexural yielding and the shear crack. In this paper, an investigate or the system currently in use was analyzed for various modes of failure and then best suitable component of jib crane is cantilever I-type beam for the analysis and furthermore the results are compared with FEA software- ANSYS. Also the results obtained are plotted for von misses stress distribution and maximum stress and maximum deformation is obtained on the various windows in this paper.
(Paper ID: 26ET3005201507)
Role if librarian in Digital Economy
Document Information:
Title: Role if librarian in Digital Economy
Author(s): Ms. Hansa Bhoj, Phd scholar, Rai university, librarian college of Dental Science, Amargadh
Citation: Ms. Hansa Bhoj. "Role if librarian in Digital Economy", IJFTET, Volume: II , Issue: VI Publication Year: 2015 , Page(s): 28-30.
Keywords: Role of Librarian, Internet, World Wide Web, Data Mining, Meta Data, Latent Semantic Indexing, Intelligent Agents, Search Intermediary, Facilitator, End-User Trainer, Web Site Builder, Researcher, Interface Designer, Knowledge Man- ager, Sifter.
Article type: Research paper
DOI: 30/05/2015 http:http://ijftet.wix.com/research#!vol-ii-issue-vi-may15/cxz0 (Permanent URL)
Publisher:Akshar Publication
Abstract: A library plays a vital role in universities and information management science because it is not only interdisciplinary but also encompasses all the aspects of information management using digital technology. Libraries may be on the verge of a revolutionary phase of integrating technology in all their services in order for them to become effective information providers in the digital economy. In much of the literature on the potential of ICTs in academic libraries, it is argued that advancements in ICTs are changing the way people are accessing and using information. A librarian is the heart of library as he or she is the main resource of library management system in the digital world. Integration of ICTs in library services is necessary if libraries are to effectively provide information at anytime and anywhere. The chapter reviews various similar sources that looked at technology and its impact on library services. The scope of modern libraries has been expanded to even business world; it is not limited to academic activities. Modern libraries contribute to business more significantly than traditional libraries. Due to the advancement of digital technology; a new global digital economy has emerged. The emerging digital economy is global in scope. It promises to establish a global community in which we will discover and invent new ways to work. Learn, teach, think and play. Radical changes can be expected in the workplace, education, health, financial services and leisure activities. A key to the success of the digital economy is the realization of electronic commerce. Businesses, government, non-profit organization and individuals alike will play an important role in the transition to electronic commerce and the digital economy. This article seeks to address this issue with a focus on the role of librarian in the digital economy.
(Paper ID: 26ET3005201508)
Technical Literature Review on Ship Propulsion System
Document Information:
Title: Technical Literature Review on Ship Propulsion System
Author(s): Mr. J. B. Solanki, Lecturer, Electrical Dept., B.& B. Institute of Technology, Vallabhvidyanagar, Gujarat. Mr. K. K. Bhatt, Asst. Professor, Electrical Dept., Government Engineering College, Gandhinagar,Gujarat. Mr. A. A. Parmar, Lecturer, Electrical Dept., B.& B. Institute of Technology, Vallabhvidyanagar, Gujarat. Mr. A. P. Shah, Lecturer, Electrical Dept., B.& B. Institute of Technology. Vallabhvidyanagar, Gujarat.
Citation: Mr. J. B. Solanki, Mr. K. K. Bhatt, Mr. A. A. Parmar & Mr. A. P. Shah. "Technical Literature Review on Ship Propulsion System", IJFTET, Volume: II , Issue: VI Publication Year: 2015 , Page(s): 31-40.
Keywords: HTS motor, Ship propulsion system, Controller, Electric drive.etc.
Article type: Research paper
DOI: 30/05/2015 http:http://ijftet.wix.com/research#!vol-ii-issue-vi-may15/cxz0 (Permanent URL)
Publisher:Akshar Publication
Abstract: This paper present whole electrical drive used in ship propulsion system (SPS). Here detailed explanation of all the part used in SPS is discussed. Also in power modulator different drives for different motor compared .Rapidly development of High-temperature superconductors (HTS) used in motor which is more advantageous for ship propulsion system. Different conventional motor used in SPS has been compared with HTS motor.
(Paper ID: 26ET3005201509)
Fail-Safe System for CNC Lathe Machine Tool in Suddenly Power Cut Off Condition
Document Information:
Title: Fail-Safe System for CNC Lathe Machine Tool in Suddenly Power Cut Off Condition
Author(s): Mr. Digvijaysinh M. Rana, ME Scholar, Mechanical Department, SVIT, Vasad, Gujarat, India. rdigvijay6@gmail.com. Prof. Vishwanath S. Bali, Assistant Professor, Mechanical Department, SVIT, Vasad, Gujarat, India. viswabali@gmail.com
Citation: Mr. Digvijaysinh M. Rana & Prof. Vishwanath S. Bali. "Fail-Safe System for CNC Lathe Machine Tool in Suddenly Power Cut Off Condition", IJFTET, Volume: II , Issue: VI Publication Year: 2015 , Page(s): 49-53.
Keywords: Fail safe mechanism, Solenoid valve, Coupling, Tool holder.
Article type: Research paper
DOI: 30/05/2015 http:http://ijftet.wix.com/research#!vol-ii-issue-vi-may15/cxz0 (Permanent URL)
Publisher:Akshar Publication
Abstract: In today’s industrial field production become fast due to use of various automation system. Now days more and more traditional and cnc machine tool used in automated production line. Sometime due to unavoidable causes like machine failure, disconnect the machine from power line , the cutting operation going to be stop and this will damage the work piece and tool. However some time due to suddenly power cut off there will be over travel of cutting tool till the motor shaft running stop in traditional machine tool.(in auto feed operation). And cnc machine , when suddenly power cut off although the servomotor stops quickly it stops the tool or work piece motion in cnc lathe or cnc milling respectively , the tool and work piece damage or fail occurs due to over load. So by applying the different mechanical back through motion mechanism, tool moves in opposite direction to that of the feed. The use of mechanism that will stop the motion of the tool or work piece whichever is less, this will also stop the cutting operation even after loss of the control on the machine. This will be safe guard the work piece and tool from damage.
(Paper ID: 26ET3005201510)
Process Parameters Effect of Resistance Spot Welding on Weld Quality
Document Information:
Title: Process Parameters Effect of Resistance Spot Welding on Weld Quality
Author(s): Mr. P. H. Solanki, Pursuing M.E. Mech. (Prod. Engg.), Atmiya Institute of Technology & Science, Rajkot(GTU), prashanthsolanki@gmail.com, Prof. M. S. Kagthara, Assistant Professor (Mech. Engg.), Atmiya Institute of Technology & Science, Rajkot(GTU), mskagthara@aits.edu.in. Mr. N. J. Chotai, Managing Partner, Saurashtra Tin & Metal Industries, Rajkot. nitin@saralgroup.com.
Citation: Mr. P. H. Solanki, Prof. M. S. Kagthara & Mr. N. J. Chotai. "Process Parameters Effect of Resistance Spot Welding on Weld Quality", IJFTET, Volume: II , Issue: VI Publication Year: 2015 , Page(s): 41-48.
Keywords: Resistance Spot Welding (RSW), Weld Quality, Tensile Strength, DMAIC, Taguchi Method.
Article type: Research paper
DOI: 30/05/2015 http:http://ijftet.wix.com/research#!vol-ii-issue-vi-may15/cxz0 (Permanent URL)
Publisher:Akshar Publication
Abstract: Resistance Spot Welding is a process of joining the sheet metal parts. In this study spot welding machine is used to weld the pads on a pan of the fuel tank. Material used in fuel tank’s pan and pad is Cold Reduced Low Carbon Steel Sheet. The thickness for pad is 1.50 mm and for pan is 0.80 mm (Galvanized). The diameter of electrode used for spot welding is 5mm. There is a rejection of fuel tank due to low weld tensile strength. So, DMAIC (Define, Measure, Analyse, Improve & Control) method and Taguchi Method is used for reduction in rejection level. Experiment is carried out on Resistance Spot Welding machine. The highly effective parameters as welding current and weld cycle time with their different levels are used. These parameters are affecting the quality of resistance spot welding in terms of tensile strength, nugget size and internal defect. Each parameter has its effect on output quality parameter. The purpose of this study is to find out the effect of two control parameters like welding current and weld cycle time of resistance spot welding machine on tensile strength, nugget size and internal defect of the spot welding as a weld quality. Ultrasonic Flaw Detection Test as a Non-Destructive test and Tensile Test as a Destructive test is used. Optimization of welding current and cycle time by using software is used for reduction in rejection level.